Padholdr Ram Lock Series Lock and Dock iPad Dash Kit 2007 -2011 Toyota Camry

Description

Padholdr Ram Lock Series Lock and Dock iPad Dash Kit 2007 -2011 Toyota Camry.
Vehicle Service Type Automobile
Compatible Devices Tablets
Brand PADHOLDR
Special Feature Adjustable
INDASH
by
paeJ
MOUNTINGLOCATION:
Right Side of Radio Cavity K R
TOOLS REOUIRED:
Flat Dash Tool. Hook tool
Phillips Screwdriver
10mm Socket Driver
HARDWARE INCLUDED:
(3)A-#8x9/16"Needle Pt.Screw
INSTALLATION INSTRUCTIONS
PART#:75137-107
MFG: TOYOTA
MODELS & YEARS:
Camry 2007-2011
(Auto&Man Trans)
STEP#1: Unscrew Shifter Knob. Remove the cover on the left side of the cubby and lower
side of the climate control by grasping it with your hands and pulling out towards you to
release (2) clips. Repeat on the right side.
STEP #2 Remove the Shifter cover. (W/AT) Open the cup holder door on the console. With
hook tool lift up on the cover that surrounds the shifter and goes to the front of the cubby
(L-Shaped). Lift releasing (6) plastic claws and (3) clips. Disconnect seat heater plugs if
applicable. Set aside. (W/MT) Open the cup holder door on the console. Carefully lift or pry
up on the shifter bezel from behind the bezel at the cup holder opening releasing (2) clips. Lift
up bezel continuing to release (3) more clips to the front of the bezel. Pull bezel towards you
to disengage (2) claws that go into the bottom of the cubby,
STEP #3: To remove the console top in front of the arm rest, begin by opening the console
arm rest door. With your hands and/or hook tool assist, lift up at the sides of the console top
box directly in front of the arm rest, lift to release (2+) clips. Continue lifting to release a total
of (3) claws and (5) clips holding this bezel in place. Disengage the clamp for power outlet
wire, and disconnect the plug. Set console top cover aside.
STEP #4: With Phillips screwdriver remove the (2) screws to the sides of the cubby. Then
pull out the cubby releasing (4) claws. Disconnect the plugs, and set aside.
STEP #5: With flat dash tool remove the air vent assembly by inserting the tool into the left
side between the air vents and dash. Tilt the tool to assist to release (2) clips. Repeat on the
right side releasing (2) more clips. Pull out the air vent assembly towards you releasing the last
(2) clips. Disconnect plug and set aside.
STEP#6: With 10mm Socket Driver remove the (4) blots that hold the radio and climate control
in place. Pull the radio and climate control assembly out releasing (4) clips. Set it down onto
the shifter console.
STEP #7: Install InDash Mount onto the flat are to the right of the radio, between the (2) clip
slots. Install the (2) supplied screws into the holes. (NOTE: Third hole is avialable for the third
screw only if necessary for increased stability.)
STEP #8: Replace the radio and climate control assembly, and all other components and plugs
in reverse order. Be careful of the tabs in the front of the console cover must fit into the
console correctly
75137-107
Page 1 of I
* * ADVISEMENT **
Read instructions completely prior to
starting installation. All InDash Mounts
are designed so that after installation,phone
is facing normal driver position for left-
hand drive vehicles. This mount is not
designed to be used in foreign countries
with right-hand drive vehicles. Use extreme
care When working around the plastic
componenisonthedash.-xeesstoree.can
cause breakage of the plastic components
Side cover removal
Shiftercoverremoval
Air Vent removal with tool
Console top removal
08-29-11
InDash Mount installed
Mount installed w/ 2of3 screws
woR
There may be recent updates to this Instruction Sheet, please visit website or contact PanaVise Products, Inc, for the latest revision